河南理工大学微机原理课设--遥控窗帘.docVIP

#includestc10.h #define uint unsigned int #define uchar unsigned char sbit K1=P3^6; sbit K2=P3^7; sbit key1=P0^5; sbit key2=P0^6; sbit key3=P0^7;//按键定义 sbit a=P2^0; //A数据接口 sbit b=P2^1; //B数据接口 sbit c=P2^2; //C数据接口 sbit d=P2^3; //D数据接口 sbit in1=P2^4; // sbit in2=P2^5; // sbit en=P2^6; //使能开关 sbit huo1=P3^2;//霍尔传感器扫描接口 sbit huo2=P3^3; sbit light=P3^4;//光敏扫描口 sbit D10=P2^7; sbit D12=P3^5; bit i=0,j=0; int v=100,ms=0,mms=0,s,sec,n=0,m=0,k1=6,k2=12,minu,hour,in; uchar open[]={0x54,0x7b,0x73,0x5c}; //{0x5c,0x73,0x7b,0x54}; uchar close[]={0x6d,0x5c,0x30,0x58};//{0x58,0x30,0x5c,0x6d}; uchar stop[]={0x73,0x5c,0x78,0x6d};//{0x6d,0x78,0x5c,0x73}; uchar good[]={0x5e,0x5c,0x5c,0x6f};//{0x6f,0x5c,0x5c,0x5e}; uchar table[]={0x3f,0x06,0x5b,0x4f,0x66, 0x6d,0x7d,0x07,0x7f,0x6f};//字型码 uchar q[]={0,0,0,0}; uchar qq[]={0,0,0,0}; uchar wei[]={0xf7,0xfb,0xfd,0xfe};//位选码 void delay(uint x) //延时子函数 { uchar y; for(;x!=0;x--) { for(y=100;y!=0;y--) {;} } } void display(uchar *pp,uchar *p)//显示函数 { uchar y; for(y=0;y4;y++) { P0=wei[y]; P1=pp[p[y]]; delay(25); } } void display1(uchar *p)//显示函数 { uchar y; for(y=0;y4;y++) { P0=wei[y]; P1=p[y]; delay(25); } } //对已经选择好的模式进行掉电储存 /*********关闭IAP功能**********/ void closeiap() { IAP_CONTR=0; IAP_CMD=0; IAP_TRIG=0; IAP_ADDRH=0x80; IAP_ADDRL=0x00; } /***********IAP读********************/ unsigned char readiap(unsigned int add) { unsigned char dat; IAP_CONTR=0x83;//0x80:SYSCLK30M, 0x81:SYSCLK24M, 0x82:SYSCLK20M, 0x83:SYSCLK12M IAP_CMD=0x01;//0：无操作 1:读， 2：写， 3：删除 IAP_ADDRH=add8; IAP_ADDRL=add%256; IAP_TRIG=0x5a; IAP_TRIG=0xa5; //IAP命令生效 delay(3); dat=IAP_DATA; closeiap(); return(dat); } /*************IAP写******************/ void writeiap(unsigned int add,unsigned char dat) { IAP_CONTR=0x82; IAP_CMD=0x02; IAP_ADDRH=add8; IAP_ADDRL=add%256; IAP_DATA=dat; IAP_TRIG=0x5a; IAP_TRIG=0xa5; //IAP命令生效 delay(3); closeiap(); } void d