W2L500020 链路聚合 教师参考.docVIP

链路聚合 配置二层静态聚合 搭建实验环境 首先，依照图示完成A与B的配置A的IP地址为1.168.0.1/24，网关为1.168.0.253；配置主机B的IP地址为1.168.0.2/24，网关为1.168.0.254。[SWA]vlan 10_ [SWA-vlan10] port GigabitEthernet 1/0/4 [SWA]int vlan 10 [SWA-Vlan-interface10] ip add 192.168.0.253 255.255.255.0 [SWB]vlan 10 [SWB-vlan10] port GigabitEthernet 1/0/4 [SWB]int vlan 10 [SWB-Vlan-interface10] ip add 192.168.0.254 255.255.255.0 完成trunk基本配置。在SWA、SWB上配置各自以太网端口GigabitEthernet1/0/1～GigabitEthernet1/0/3的链路类型为Trunk类型，允许指定的VLAN1、VLAN10通过当前Trunk端口。请在下面的空格中补充完整的命令： [SWA]interface GigabitEthernet 1/0/1 [SWA-GigabitEthernet1/0/1]shutdown [SWA-GigabitEthernet1/0/1] port link-type trunk [SWA-GigabitEthernet1/0/1] port trunk permit vlan 1 10 [SWA]interface GigabitEthernet 1/0/2 [SWA-GigabitEthernet1/0/2]shutdown [SWA-GigabitEthernet1/0/2] port link-type trunk [SWA-GigabitEthernet1/0/2] port trunk permit vlan 1 10 [SWA]interface GigabitEthernet 1/0/3 [SWA-GigabitEthernet1/0/3]shutdown [SWA-GigabitEthernet1/0/3] port link-type trunk [SWA-GigabitEthernet1/0/3] port trunk permit vlan 1 10 [SWB]interface GigabitEthernet 1/0/1 [SWB-GigabitEthernet1/0/1]shutdown [SWB-GigabitEthernet1/0/1] port link-type trunk [SWB-GigabitEthernet1/0/1] port trunk permit vlan 1 10 [SWB]interface GigabitEthernet 1/0/2 [SWB-GigabitEthernet1/0/2]shutdown [SWB-GigabitEthernet1/0/2] port link-type trunk [SWB-GigabitEthernet1/0/2] port trunk permit vlan 1 10 [SWB]interface GigabitEthernet 1/0/3 [SWB-GigabitEthernet1/0/3]shutdown [SWB-GigabitEthernet1/0/3] port link-type trunk [SWB-GigabitEthernet1/0/3] port trunk permit vlan 1 10 注意： 为了避免广播风暴，请shutdown交换机上相关端口。 配置二层静态聚合 在SWA上创建二层聚合端口1，并采用默认静态聚合模式。配置Bridge-Aggregation端口下配置，与聚合组中端口下配置一致。请在下面的空格中补充完整的命令： [SWA]interface bridge-aggregation 1 [SWA-Bridge-Aggregation1] port link-type trunk [SWA-Bridge-Aggregation1] port trunk permit vlan 1 10 在SWA上分别将端口GigabitEthernet1/0/1至GigabitEthernet1/0/3加入到静态聚合组1中。请在下面的空格中补充完整的命令： [SWA] interface gigabitethernet 1/0/1 [SWA-GigabitEthernet1/0/1] port link-aggregation group 1 [SWA] interf