ESRITopologyRuleType简述.docVIP

序号 esriTopologyRuleType 英文描述 中文描述 图片描述 (红色为拓扑错误) ArcGIS Desktop中对应的命令 1 esriTRTAny The rule type can be any. Used when querying 2-27定义的规则中任何一种，一般在查询时使用。请注意，不要将esriTRTAny直接作为拓扑规则进行赋值给ITopologyRule使用，会抛出自动化的错误。 无 无 2 esriTRTFeatureLargerThanClusterTolerance The rule is a feature to be deleted is smaller than the cluster tolerance rule. 任何一个拓扑都具有的内在规则，它是定义在拓扑容限之内的要素被删除的规则。 无 无 3 esriTRTAreaNoGaps The rule is an area-no gap rule. 针对面状图层内的，是定义图层内面状要素间没有缝隙的规则，。 Must Not Have Gaps 4 esriTRTAreaNoOverlap The rule is an area-no overlap rule. 针对面状图层内的，是定义图层内面状要素间没有重叠的规则，。 Must Not Overlap 5 esriTRTAreaCoveredByAreaClass The rule is an area covered by area class rule 针对面状图层间的，定义图层间区域要素覆盖的规则。如果第二个图层中的面要素不为第一个图层中的任一面要素所覆盖的话，视为拓扑错误。 Must be covered by Feature Class of 6 esriTRTAreaAreaCoverEachOther The rule is an 2 areas cover each other rule 针对面状图层间的，定义两个图层间的区域要素必须互相覆盖的规则,这个规则实际上要素两个图层间的要素是一样的。 Must Cover each other 7 esriTRTAreaCoveredByArea The rule is an area covered by area rule 针对面状图层间的，定义图层间区域要素覆盖的规则。如果第一个图层中的区域要素不为第二个图层中的任一区域要素所包含的话，视为拓扑错误。 Must Be Covered By 8 esriTRTAreaNoOverlapArea The rule is an area covered by area rule 针对面状图层间的，定义图层间区域要素不能互相覆盖的规则。 Must Not Overlap with 9 esriTRTLineCoveredByAreaBoundary The rule is a line covered by area boundary rule 针对线状图层与面状图层间的，定义一个线状图层的线要素必须为一个面状图层的面要素边界所覆盖的规则。线要素的任一部分如果跟面要素边界不符合，都视为拓扑错误。 Must Be Covered by Boundary Of 10 esriTRTPointCoveredByAreaBoundary The rule is a point covered by area boundary rule 针对点状图层与面状图层间的，定义一个点状图层的点要素必须为一个面状图层的面要素边界所覆盖的规则。点要素的任一部分如果跟面要素边界不符合，都视为拓扑错误。简单地说，点必须全部落在面要素边界上的规则。 Must Be Covered by Boundary Of 11 esriTRTPointProperlyInsideArea The rule is a point properly inside area rule 针对点状图层与面状图层间的，定义点状图层的要素必须落在面状图层要素之内的规则。任何落上面状图层中要素边界或者之外的都视为拓扑错误。 Must Be Properly Inside 12 esriTRTLineNoOverlap The rule is a line-no overlap rule 针对线状图层内的，定义线要素之间不互相重叠的规则。互相叠盖的部分都视为拓扑错误。 Must Not Overlap 13 esriTRTLineNoIntersection The rule is a line-no intersection rule 针对线状图层内