JV菜单全.xls

Sheet3 Sheet2 Sheet1 MEDIA COMP. HEATER SET TEMP. SET TIME PRINT MODE DRAFT QUALITY FINE QUALITY SCAN DIRECTION LOGICAL SEEK INK LAYERS DRYING TIME AUTO CUT PRE-FEED MARGIN COLOR PATTERN REFRESH VACUUM FeedSPEED LEVEL PRIORITY ALL HOST ALL PANEL INDIVIDUALLY AUTO CLEANING Print.CLEANING MEDIA DETECT DETECT METHOD CUTTING DETECT SETUP RESTET PRE: PRT: POST: STANDBY OFF TIME NONE 0-90MIN 540X720 540X900 540X1080 PASS SCAN 4/6/8/12/24/36 720X540 720X720 720X1080 720X1440 ON/OFF QUALITY QUALITY ON/OFF 1-9 SCAN DRAW.END 0.0-19.9S 0.0-19.9S LEFT RIGHT -10mm-85mm LEVEL 0-3 10%-200% MEDAI COMP. HOST/PANEL HEATER PRINT MODE INK LAYERS ORYING TIME AUTO CUT PRE-FEED MARGIN REFRESH VACUUM Feed SPD.LEVEL TYPE INTERVAL TYPE 10mm-10000mm NORMAL/HARD/SOFT SELECT/WIDTH BOTH EDGE LEFT EDGE RIGHT EDGE NONE HI SPEED/NORM SPD ST.MAINTENANCE CARRIAGE OUT WIPER EXCHANGE NOZZLE WASH PUMP TUBE WASH CUSTODY WASH CR.MAINTENANCE HD.MAINTENANCE DROP.POSCORRECT SLEEP SETUP ON/OFF/1h-168h CLEANING NORMAL/SOFT/HARD ROUNTINE SETUP ROUNTINE WIPING SCAN COUNT 0-9990 TEMP.diff 0-60 NORMAL/SOFT/HARD AQUA SOL EXCHG WIPER LEVEL 1/10-10/10 InkTANKExchange MEDIA RESIDUAL 步进值校准 OFF:0-50℃ 设定加热开始结束时间 设定前中后三级加热 质量：精细/快速/标准 设定打印精度 设定打印精度 设定PASS 设定高/低速 FINE/FAST/STD. 设定单双向 设定逻辑打印 设定叠印次数 设定干燥时间 设定是否自动裁纸 打印前是否前后检测走纸 设定左右留空区 是否使用机器管理颜色 设定吸风强度 设定走纸的速度 所有设置计算机优先 所有设置写真机优先 定制优先权 是否自动检测纸张宽度 设定裁纸时的测纸方式 重置TYPE参数 STANDARD/STRONG/OFF/WEAK/LittleWEAK 喷车移出墨栈 更换刮板 喷孔清洗 墨泵清洗 喷车移出到维护区 FILL UP INK DISCHARGEWASH 墨路注墨 清洗墨路 MaintWashLiquid 填充清洗液 打点校准 设定关机后多少时间闪喷 设定关机后多少时间清洗喷头 设定关机后多少时间清洗墨泵 设定当环境温度与机器温度相差多少时，喷印到多少PASS刮板对喷头进行清洁 设定工作多少时间闪喷 设定工作多少时间清洗墨泵 设定工作多少时间清洗喷头 更换墨水类型 设定检测刮板的计量次数 更换废墨桶 DEODORIZE FAN STOP TIME RENEW DRYNESS FEED STAMP SETUP WasteInkWarning MRL COMMAND OFF/CONTIUNE/0-240Min ITEM TEST DRAW PAGE NO. PRINT EXTEND ONLINE/ALL SCAN DIR/FEED DIR MRL-III(JV33)/MRL-II(JV3) TestDrawArrange 打印测试条的方式 打印机接收指令 CONFIRM.FEED BACK FEED TIME SET XXXX.XX.XX XX:XX:XX UNIT SETUP LENGTH TEMP. ℃/℉ mm/inch MACHINE NAME JV33-01/99 DYE BUZZ