安装滑轨路轨的资料.pptVIP

Specification For Bassett * DEADLINE—All Production Must Include These Features March 1,2006 * * DRAWER—All Production Must Include These Features February 1,2006 期限: 所有的産品必須在3/1/06年前按此要求做 抽屜: 所有的産品必須在2/1/06年前按此要求做 Revised 3/20/2006 English Dovetails *Dovetails Are On 1” Center 榫頭要1”居中 * 5/16” Tapered Dovetails Per Drawing 榫頭要是5/16”的錐形. * Dovetails Should Be Smooth And Flush 榫頭要平滑 * Dovetails Must Be Finished Consistent With Drawer sides After Sanding 榫頭要與抽側一樣砂光及油漆 * Gaps And Voids Are Not Acceptable 不接受榫頭間有空隙 * No Partial Dovetail On Drawer Side抽側不要有不完整的榫頭 * Bottom Groove In Side And Back Will Be Hidden Within Bottom Dovetail.抽底抽側有底板槽的要隱藏在燕尾榫下. * Top Edge Of Drawer Side And Back Will Have 7/16” Radius. 抽側與抽後頂端都要有 7/16”的倒角 * Minimum 2 Dovetails, Min. Width Side 2-1/4” Anything Less Will Be Tray Front 最少要有2個榫頭, 抽側最少寬度是2/1-4”, 小於此的為 tray. * Side Guided Drawers May Be English Box Construction 側邊滑軌的抽屜用英式四面的抽屜結構 * Non-Wood Tone Cases Will Have Coordinating Drawer Color. 沒有木紋的抽側要與外部顔色一致 Finished Fronts/Sides/Backs/Bottoms * Minimum Finish Thickness Is 1.5 MIL油漆最少要有1.5MIL厚 * Finish Will Be Clear Coat. 油漆要透明漆. * Sides And Back Will Be Clear Solid Hardwood, Edge Glued Minimum 1” Strips. 抽側和抽後要是乾淨的硬實木, 若需拼板, 拼板寬度最小要有1” * Side And Back Will Be 11 MM Minimum Thickness Also Will The Same Width .抽側和抽後要有11mm厚. Bassett Nameplate Will Be Located 1” Down From Top Edge And 2” Back From Back OF Drawer Front Top Left Hand Drawer Only. Bassett. 名牌要釘在左邊抽側板上, 距抽側上1”, 距抽前板2”. *Drawer Sides, Backs, Bottoms Color Will Be Predicated On A Range Select By The Merchandising Team 抽側, 抽前, 抽底板的顔色要在 Bassett 要求範圍內 *All Bottom Drawers In Storage Pieces Will Be Cedar Lined Bottom (Unfinished) Can Be Drop In Liners 用來放東西的抽底要用香杉, 不用油漆 *Clear Coat Back Of Drawer Front. 抽前板的反面要做透明漆 * Drawer Bottom Thickness 3MM. 抽底要有3mm厚 * Silver Trays-All Dining Storage Cases. 餐廳碗碟櫃要放銀器盒. Drawer Stop Screw Size Will Be #6 X 5/8” Flat Head “ C-Stop” C 型塑膠擋片 C型的抽擋片, 平頭螺絲尺寸 為 #6x5/8” Glue Blocks 4 Glue Blocks