模具专业英语重要词汇（Glossary of important terms in Mould Specialty English）.docVIP

下载本文档

14
0
约5.9千字
约 18页
2017-09-23 发布于河南
举报
版权申诉

模具专业英语重要词汇（Glossary of important terms in Mould Specialty English）.doc

1、有哪些信誉好的足球投注网站（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

模具专业英语重要词汇（Glossary of important terms in Mould Specialty English）

模具专业英语重要词汇（Glossary of important terms in Mould Specialty English） Glossary of important terms in mould English - - English for mould - Inlet: Gate enter position: gate location nozzle form: gate type large nozzle: edge gate- Fine nozzle: pin-point gate nozzle size: gate size rotary nozzle: switching runner/gate- Sprue diameter: sprue diameter- - Two, runner: runner- Runner: hot runner, hot manifold hot sprue/cold runner-: hot runner mouth cold DC: direct sprue gate sprue runner: round full/half runner- (Circular Flow channel computer analysis: mold flow analysis runner balance: runner balance- Hot mouth: hot sprue hot runner plate: hot manifold- Heating tube: cartridge heater probe: thermocouples- Plug: connector plug socket: connector socket- Sealing / sealing: seal- - Three, transport water: water line throat plug: line lpug - Venturi: Tube - Plastic pipe: plastic tube quick joint: jiffy, quick, connector- Plug/socker- - Four, mold parts: mold components- - Three plate mold: 3-plate mold second board mold: 2-plate mold- Side nail / side: leader, pin/guide, pin, side, division / guide sleeve: bushing/guide, bushing- Naka Toshi: shoulder, guide, bushing, L:guide, pin- Ejector plate: ejector, retainner, plate pallet: support plate- Screw: screw pipe nail: dowel pin- Mold opening groove: ply, bar, scot, inner mould tube position: core/cavity inter-lock- Thimble: ejector pin barrel: ejector sleeve- Ejector pin: ejector pin pusher: stripper plate- Ha: movable, core, return, core, core, puller- Button machine (nylon hook): Nylon latch lock: lifter- oblique top Base (frame): mold base: cavity insert- model Lower internal die: core insert line (slider): slide- Insert: insert press seat / slant chicken: wedge- Wear plate / oil plate: wedge, wear, plate layering: plate- Hold head: support pillar: sprue bushing- sprue Bezel: stop plate positioning ring: locating ring- Lock: latch button chicken: parting, lock, set- Putter: push, bar, bolt, screw: S.H.S.B- Top panel: eracuret