清除配置（Clear configuration）.docVIP

清除配置（Clear configuration） Cisco删除配置 Erase startup config Erase running config Delete VLAN.DAT Reload H3C Reset saved configuration The saved Configuration will be Erased. Are you sure? [y / n] and Configuration in Flash memory is being cleared. Please wait... Unit1 file does not exist! H3C 然后直接拔电重启 迈普 Reload default 1.system-view 进入系统视图模式 2、sysname 为设备命名 3、display Current Configuration 当前配置情况 4、 Language mode English Chinese | 中英文切换 5、interface Ethernet 1 / 0 / 1 进入以太网端口视图 6 Port Link Type | | Hybrid 设置端口访问模式 Trunk Access 7 打开以太网端口 undo shutdown 8 关闭以太网端口 shutdown 9、 Quit 退出当前视图模式 10、 VLAN 10 创建vlan 10并进入vlan 10的视图模式 11、 Port Access VLAN 10 在端口模式下将当前端口加入到vlan 10中 12、port E1 / 0 / 2 to E1 / 0 / 5 在vlan模式下将指定端口加入到当前vlan中 13、port 允许所有的vlan通过 Trunk permit VLAN all H3c路由器 # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # 1、system View 进入系统视图模式 2、sysname R1 为设备命名为r1 3、display IP Routing Table 显示当前路由表 4、 Language mode English Chinese | 中英文切换 5、interface Ethernet 0 / 0 进入以太网端口视图 6 配置ip地址和子网掩码 IP address 192.168.1.1 255.255.255.0 7 打开以太网端口 undo shutdown 8 关闭以太网端口 shutdown 9、 Quit 退出当前视图模式 10、 ip route static Description to.r2 配置静态路由 192.168.12.2 192.168.2.0 255.255.255.0 11、 ip route 0.0.0.0 0.0.0.0 192.168.12.2 to.r2 配置默认的路由 static description Switch H3C S3100 H3C S3600 Switch H3C router MSR 20 - 20 # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # 1、调整超级终端的显示字号; 2、捕获超级终端操作命令行, 以备日后查对; Language mode English Chinese | dissipationsun 中英文切换; 4、复制命令到超级终端命令行, 粘贴到主机; 5、交换机清除配置: H3C Reset SAVE; H3Creboot; 6, routers and switches can not be switched off when connected, must be connected before testing Check the connectivity of the network and dont make the lowest mistake. 7 and 192.168.1.1/24 are equivalent to 192.168.1.1 255.25