注塑机控制参数的设定（Control parameter setting of injection molding machine）.docVIP

下载本文档

10
0
约1.97万字
约 21页
2017-08-15 发布于河南
举报
版权申诉

注塑机控制参数的设定（Control parameter setting of injection molding machine）.doc

1、有哪些信誉好的足球投注网站（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

注塑机控制参数的设定（Control parameter setting of injection molding machine）

注塑机控制参数的设定（Control parameter setting of injection molding machine） This excerpt is from Cai Hengzhi, Xie Shuqing and Wang Wenguangs injection molding operator Thank you! Control parameter setting 1. mode locking parameter There are 4 parameters: locking clamping speed. The 4 clamping pressure. Location of each die clamping stage. Each lock mode stage Time. As mentioned earlier, the die locking process is divided into 4 sections. First, the template is moved at a high speed to lock the die until it is set to a fast clamping position When the value is finished, the switch is converted to the medium speed mode locking stage, and the locking action is buffered so as to protect the die and move stably When the die reaches the low pressure clamping position, it enters the low pressure lock mode, at this time the clamping force drops to the low pressure immediately No obstacles can be smoothly into the high pressure lock mode, if the mold is caught between the foreign body or the mold guide, the guide sleeve is not good, If the pressure is too low, the locking motion will stop. When the low-voltage mode locking time arrives, the template can not enter the state of high voltage mode locking, The alarm system is started, the machine alarms automatically and the mold is opened. This can achieve the purpose of mold protection. The clamping process is shown in figure. There is a high voltage detection time in the process of high voltage mode locking to die termination, if the machine fails to lock the mold to the termination confirmation within the specified time, The alarm is sent out, so that you need to re adjust the model or check if the high voltage monitoring time is too small. Low voltage transfer High voltage point Low speed turn Low voltage point Quick turn Low velocity point (speed) Full lock Die position high pressure Low speed low voltage fast Mold stop position The machine off clamping process In the process of setting up the die, the parameters of the locking acti