FQA检验员培训教材.pptVIP

DANAHER SETRA-ICG(TIANJIN)CO.,LTD. Thank you… Encoder-from FQA June.14---Harold.Liu 编码器－来自于FQA PCB 中心孔有胶 Coating inside the center hole of PCB Encoder-from FQA June.15---JY.Shi 编码器－来自于FQA Base damaged by clip 底座被夹子压坏 LED are in contact with the tether –from customer Parvex F10-May.23---JY.Shi LED 接触TETHER－来自于PARVEX顾客－F10 Action: change height of LED lead bend 措施：改变LED弯曲高度 Failed part－不合格产品 After change 改变后 压力开关培训内容 顾客投诉-GEMS FS-380组装线缆不良 Encoder -from FQA-6.25-JY.Shi Clip issue---second time, the first time is 15th.June---OP8 编码器－来自于FQA 线夹问题 Encoder -from FQA-6.26-JY.Shi Wire too long in product end---OP8 编码器－来自于FQA 线太长 Encoder -from FQA-6.26-JY.Shi 胶！！！---OP8 PCBA-from encoder cell on June.26---JY.Shi 没点胶！！！1/16 -OP8 金属碎屑-FQA 29th.June--- encoder cell LED焊接不良-FQA 6th.July--- encoder cell Encoder-FQA 10th.July--- encoder cell 多余金属线头 Encoder-FQA 10th.July--- encoder cell/ PCB cell 元件贴歪 Encoder-FQA 10th.July--- encoder cell Wire damaged 编码器－来自于FQA 线损伤 Encoder-FQA 12th.July--- encoder cell 多余的焊锡 Unwanted soldering Encoder-FQA 14th.July--- encoder cell 多余的金属线头 Unwanted metal wire-repeat issue Encoder-FQA 14th.July--- encoder cell 没点胶 No glue-repeat issue Encoder-FQA 14th.July--- encoder cell 没装热缩管 Without shrink tube Encoder-FQA 17th.July--- encoder cell 线损坏 Wire damaged-repeat issue Pin of LED too close to the metal ring. LED针太紧 Scratch on hub surface HUB表面划伤 Overflow Glue 溢胶 Scratch on hub surface HUB表面划伤 Wrong cover 错误的壳 Screw not be screwed all the way 螺丝没有拧紧 Overflow Glue 溢胶 Have no marking 没有标注 Screw not be screwed all the way 螺丝没有拧紧 Dirty inside cover 壳体内部脏 返工后助焊剂残留，没有保护胶。 附件少六角扳手,少螺钉-FQA 10th.Aug--encoder cell 未装LID,LABEL漏贴-FQA 8th.Aug--encoder cell LABEL漏贴-FQA 10th.Aug--encoder cell Encoder-from FQA June.8---JY.Shi Screw loose 螺钉松 Encoder-from FQA June.8---JY.Shi 编码器－来自于FQA Incorrect screw 附件螺钉不良 Encoder-from FQA June.12---JY.Shi 编码器－来自于FQA Bad soldering 连焊 Encoder-from FQA June.14---Harold.Liu Coating 涂敷不均匀,红色区域没有. No coating in red area Wuxi Wanli complain