JBT 10116-1999机床夹具零件及部件 锥度芯轴.pdf

ICS 25.080.01J44JB中华人民共和国机械行业标准JB/T 10116—1999机床夹具零件及部件锥度心轴The parts and units of jigs and fixturesTaper memdred1999-08-06发布2000-01-01实施国家机械工业局发布 中华人民共和国机械行业标准机床夹具零件及部件锥度心轴JB/T 10116—1999The parts and units of jigs and fixturesTaper memdred1范围本标准规定了适用于工件直径为8~100mm的锥度心轴。2引用标准下列标准所包含的条文，通过在本标准中引用而构成为本标准的条文。本标准出版时，所示版本均为有效。所有标准都会被修订，使用本标准的各方应探讨使用下列标准必威体育精装版版本的可能性。GB/T 145—1985中心孔GB/T 1184—1996形状和位置公差未注公差值GB/T 1298—1986碳素工具钢技术条件JB/T 8044—1999机床夹具零件及部件技术要求3尺寸尺寸如下图及表所示。适用工件孔径8~50mmGB/T 1450.003工A国家机械工业局1999-08-06批准2000-01-01 实施 JB/T 10116—1999表(续)mm公称直径支号(适用工件孔径)KNod,d?211 : 300055.02454.960II55.08855.024330274.5000S : 1I55.02454.96055II455402.555.08855.02482.5155.00454.9621 : 8000II55.04655.004470418.5III55.08855.046000 : 1158.02457.960II58.08858.024SES2791 : 500058.02457.96058II58.08858.0244604073687158.00457.9620008 : 1II58.04658.004475 423 III58.08858.046000 : 1I60.02459.960II60.08860.02434028211 : 500060.02459.960II465410 6060.08860.02490I60.00459.9621 : 8000II60.04660.004480426III60.08860.046000 : 162.02461.960I08862.0241 : 5000162.02461.96062II62.08862.02447041393162.00461.9620008 : 1II62.04662.004485429 III62.08862.046I65.02440 000 : 164.960II65.08865.024350289.51 : 5000I65.02464.96065II65.08865.024475417.597.5165.00464.9620008 : III65.04665.004490433.5III65.08865.04610 JB/T 10116—1999表(续)公称直径支号(适用工件孔径)KNod,d?L2000 : 1168.02467.960II68.08868.024355294000S : 1168.02467.96068I08868.024102 168.00467.9620008 : 1II68.04668.004495438III68.08868.0461 : 3000170.02469I70.08870.0241 : 5000170.02469.96070 II70.08870.02448542540 105170.00469.9620008 : 1II70.04670.004500441III70.08870.046000 : 1172.02471.960II72.08872.0243402821 : 5000172.02471.96072 470410II72.0887200471.9621 : 8000II72.04672.004485426III72.08872.046000 : 1175.02474.960II75.08875.024350285.751 : 5000175.02474.96075II75.08875.024475413.7593.75175.00474.9621 : 8000II75.04675.004490429.75III75.08875.046176.02477.96045 000 : 1355II78.08878.024289.5000S : I178.02477.96078II78.