取钉器操作说明.docVIP

取钉器操作说明 Take?the?nails,?operating?instructions 开机 给取钉器接入DC24电源，绿、黄、红三灯齐亮一秒，同时蜂鸣器长鸣一秒，之后黄、红灯息灭，绿灯常亮，则表示取钉器开机正常。 First, the boot DC24?power?to?take?nail?access, Green, yellow, red lights With?bright quickly, At the same time?the?buzzer?blew?one second, After the?yellow,?red lights?go off, Green light, said to take the nail boot normal. 取钉操作 将硬标签放入取钉槽，并将其压下，当看到红灯亮和听到提示音（此提示音可以取消，详情见六、取消取钉的提示音）时迅速将标签上的钉子向上提起。等待钩针复位后，即可将标签从取钉槽取出。 Second, take nail operation Hard tag placed to take the nail slot, And its pressure, When you see the red light and hear a tone (Tone can be canceled, as detailed, cancel to take the tone of the nail) A rapid lift the nails on the label, After waiting for crochet reset can remove the tag from taking nail groove. 设置密码 本机在出厂时没有设置初始密码，若要给取钉器设置密码可在取钉器处于开锁状态时设置。设置密码后，在使用取钉器之前需要输入密码解锁方可使用。步骤如下： 首先，按压住取钉槽里面的软膜片并保持住（听到一声开关响才说明压到位）。 接着输入功能码：1-3-3-3-3-2，输完后黄灯开始闪烁，以提示用户输入新密码。 输入预先设置的6位密码，输入完成后蜂鸣器长鸣，黄灯停止闪烁变为常亮，接着红灯亮一秒，之后黄灯会不停的闪烁，此时密码设置成功。 在有密码的情况下开机后，黄灯会不停的闪烁，提醒用户需要输入密码解锁才可以使用取钉器。在锁定的情况下取钉器的一切功能被禁止，当执行取钉操作时红灯会闪烁并且蜂鸣器会发出嘀——嘀的报警声。 需要使用取钉器时，直接输入原来设置的6位密码，蜂鸣器长鸣一声，取钉器即解锁了。需要再次锁定取钉器时，直接输入原来设置6位密码，蜂鸣器长鸣一声，取钉器即锁定了. Third, set a password This machine is not set at the factory initial password, To take nail set a password can be set to take the nail is in the unlocked, Set your password, need to enter a password to unlock before you take nail before use. Steps are as follows: First: Suppress take the nail groove inside the soft diaphragm and hold (hear a switch ring pressure in place), 2:and then enter the function code: 1-3-3-3-3-2, Lost after the yellow light starts flashing, To prompt the user to enter a new password. 3: Enter a pre-set 6 password, Input after the completion buzzer sounding, Yellow light to stop blinking to lit, Then the red light bright a few seconds, After the yellow light will stop flashing, At this point the password set success. IF Boot password, Yellow light will stop flashing,