手动圆角机说明书英文版.docxVIP

手动圆角机说明书Instruction: Manual fillet machine一，主要用途与适用范围手动圆角机广泛用于名片，书刊，包装装潢，文件，证件，袋类，卡折，笔记本PVC卡片等切圆角。适用于纸张，纸板，菲林，PVC证件，皮革等。本机操作方便省力。轻便，操作方便，成本低。它是很受欢迎的，零维护率。ApplicationsManual fillet machine is widely used for fillet-cutting of business cards, books, package and decoration, documents, certificates, bags,and notebook’s PVC cards, etc, which applys to paper, cardboard, film, PVC certificates, leather, etc.Light weight and strength-saving, easy operation and low cost, it is popular with no needs of maintenance.二，技术规格切角高度： 30MM切角半径：R3, R4, R6, R8, R10 (随机配R6，R10，需要其他规格则要另行购买）机器尺寸：L X W X H (MM): 260 X 160 X 168 机器净重： 9KGB. SpecificationsCutting Height: 30MM;Fillet Radius: R3, R4, R6, R8, R10 (R6, R10-Random,Others-Please purchasing seperately);Dimension: 260 X 160 X 168MM (L X W X H );Net Weight: 9KG.三．调整和使用 根据切圆角半径之需，务必使用上成型刀与下成型刀相同半径的刀，待上下刀的凹凸部分吻合后拧紧压力螺钉，用一张纸实切成功后再切成品C. How to UseCut the fillet radius as required, ensure to use knife with the same redius as the upper and lower molding blades, tighten the pressure screw since the touch of concave and convex part of the upper and lower molding blades, test with a piece of paper then on products.更换刀片把压制装置3拆下把手柄1向下压到底，用锁针7插入锁针孔10，固定住刀架2把上刀4和下刀5拆下，更换所需规格的刀片先把上刀4装上固定好，再把下刀5的圆弧面跟上刀圆弧面贴紧，然后锁紧下刀把手柄1向下压，取出锁针7换刀完成Knife ReplacementⅠ. Remove paper pressing device;Ⅱ. Press to the limit of handle, plug lock pin⑦ to lock pin hole⑩，and fasten the tool carrier;Ⅲ. Replace the upper blade④ and lower blade⑤ with needed blade;Ⅳ. Fasten the upper blade④ first, touch tightly with the lower blade⑤, then lock the lower blade⑤;Ⅴ. Press the handleand remove the lock pin⑦;Ⅵ. Finished.四 维护及安全本机出厂时已调好，并经试机检验，除因为相同的圆角半径更换相应的上下刀而调整其间隙外，用户无必要时，请勿随意拆卸。调整，按动手柄时，严禁把手伸入上下刀之间D. Maintenance and SafeAdjusted and tested before shipping, it SHOULD NOT be removed unless you have special requirement or need to adjust the distance between upper and lower blades after replacing the blades.Dive your hand between upper and lower blades when operate the handle is FORBID