复合板的制造和焊接工艺（Manufacture of composite plate and welding process）.docVIP

下载本文档

0
0
约8.73千字
约 9页
2017-08-16 发布于河南
举报
版权申诉

复合板的制造和焊接工艺（Manufacture of composite plate and welding process）.doc

1、有哪些信誉好的足球投注网站（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

复合板的制造和焊接工艺（Manufacture of composite plate and welding process）

复合板的制造和焊接工艺（Manufacture of composite plate and welding process） Manufacture of composite plate and welding process Composite plate making: 1. manufacturing process: the base layer and clad layer and composite explosive welding rolling process. Type 2. 2.1 composite plate is composed of substrate and composite material. 2.2 composite steel plate in the shape of rectangular, square, round three. 2.3 size requirements: the maximum width of explosive cladding steel is 2000mm, maximum length 8000mm, maximum diameter of 4000mm, so the substrate should be controlled in the specification size. In special cases, specifically. The 2.4 substrate size requirements: Based on specifications on unilateral margin 25mm. The plate is more than 4000mm, the length of allowance plus 30mm, 25mm plus margin width The 2.5 plate material requirements: Based on substrate widening plus margin, 25mm. The splicing part, without groove, but straight mouth without slag splash. 2.6 basic and complex plate material quality requirements: cutting edge must be smooth, no slag, gap. Regardless of the substrate material or plate width must be uniform. Three Splicing requirements 3.1 base plates: allow the use of arc welding, automatic submerged arc welding. The oil must be thoroughly cleaned before welding and weld on both sides of the rust and other impurities. In the case of the base metal surface have larger pits, must be welded reinforcing, and polished. Welding must be carried out after the X - ray, 100% qualified will be flush with the base metal weld grinding. 3.2 clad welding: welding to be connected. Group of gapless. Methods: 2-3mm plate welding by manual argon arc welding. The 4-8mm board by smaw. Choice of materials: must be matched with the base metal welding material. Dont mess with the welding material. Selection of electrode is shown in Table 1 Board 0Cr18Ni9 00Cr19Ni10 0Cr18Ni10Ti 00Cr17Ni14Mo2 0Cr17Ni12 Mo2 TA2 (TI) Wire H0Cr21Ni10 H00Cr21Ni10 H0Cr21Ni10Ti H00Cr19Ni12 Mo2 H0Cr19Ni12Mo2