细纱机的传动和工艺计算fa-506（Transmission and process calculation of spinning frame fa-506）.doc

下载文档 降价啦

223
0
约5.67千字
约 7页
2017-08-02 发布于河南
举报
版权申诉
保障服务

细纱机的传动和工艺计算fa-506（Transmission and process calculation of spinning frame fa-506）.doc

1、本文档共7页，可阅读全部内容。
2、有哪些信誉好的足球投注网站（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

细纱机的传动和工艺计算fa-506（Transmission and process calculation of spinning frame fa-506） Transmission and process calculation of spinning frame I. drive system The mechanical transmission of the FA506 spinning frame is shown as follows. The drive system is as follows: Roll disk, spindle, small swing arm, level lifting wheel, double elasticity Front roller twist bar flat Winding, shaping, shaping, adding stage lifting weighing system The main gear arm is with the bottom of the pipe The electric spindle is to the main shaft Dynamic lifting of machine nail chain wheel To Twist order, twist ratio, back draft, middle roller, downward change, guide Segment change, transform, transform, gear, axis, yarn hook, short movement Gear, gear drawing, medium range lifting Transform to inter Gear shaft - rear roller - transverse movement Fig. FA506 transmission diagram of spinning frame 1. speed (1) spindle speed nm (r/min); Type: n - main motor speed (r/min); D1 - main motor pulley pitch diameter (mm), with 170180190200210 different kinds; D2 - spindle pulley diameter (mm), with a 180190200210220230240 number (2) spindle speed ns (r/min); Type: D3 - roll diameter (mm); D4 - wharve diameter (mm); Delta spindle thickness (mm) Roller speed NF (r/min) Type: ZA/ZB - twist change to the number of gear teeth, there are 38/82,45/75,52/68,60/60,68/52,75/45,82/38 kinds, Z+Z=120; ZC, ZD - twist change gear teeth, ZC have 87,85,80 three, ZD have 77,80,85 three 2. draft and draft change gears (1) mechanical drawing times Total draft multiple E: Type: ZM - drawing change gear teeth, there are two kinds of 69,51; ZN - drawing change gear teeth, there are two kinds of 28,46; ZK, ZJ - Total draft change gear teeth, with 39,43,48,53,59,66,73,81,83,84,85, 86,87,88,89 number of species The drafting ratio is E B: Type: ZH - after drafting, change the number of teeth of gear, 36,38,40,42,44,46,48,50 kinds 3. twist and twist change gears (1) calculate the twist Ttex (twist /10cm) Type: DF - diameter of front ro