手机逻辑电路常见故障（Common failure of mobile logic circuit）.docVIP

下载本文档

12
0
约 9页
2017-07-21 发布于河南
举报
版权申诉

手机逻辑电路常见故障（Common failure of mobile logic circuit）.doc

1、有哪些信誉好的足球投注网站（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

手机逻辑电路常见故障（Common failure of mobile logic circuit）

手机逻辑电路常见故障（Common failure of mobile logic circuit） 5. Common faults in logic circuits: 5.1 cannot download program analysis PCBA adopts online DOWNLOAD, and the logic circuit cannot work often causes SN/IMEI and DL failure. Here are three conditions for the logical circuit to work properly: 1. Normal operating voltage: VBAT, RTCVDD, VRF, VDDCORE; The clock is normal: 32.768 KHZ and 26MHZ; Data bus, address bus, read/write, reset, and select signal are normal. When downloading the program, the battery interface is added 3.8 V 1.5 A power source, the CPU detected the NBOOT signal as low level, and the phone entered the NBOOT mode (download mode). The current normal working current is about 90mA. If the current is low, the circuit is not working, and the power supply voltage can be checked. There is no reference clock 26MHZ, RTC clock 32.768 KHZ, its amplitude is normal. If the current is large, it indicates that some of the power supply voltage has short circuit and can be used in the case of uncharged Whether the resistance of the voltage to the ground is abnormal. Current is 0.5 A, common for VSIM, VRF2.85 V to ground short circuit; The current is 1.5a, which causes the power protection, and it is common for VBAT to short circuit, and check the circuit of components related to VBAT. Current such as normal, mobile phone in normal mode, FLASH program, had been written NBOOT test point can detect the pulse signal, the signal can be measured, speaking, reading and writing is normal, after the completion of the DL, cellphone, can measure the pulse signal to the data. 5.2, unable to enter the download status analysis Voltage, current, clock signal is normal, open DOWNLOAD software, can not enter the DL state, can check whether the serial port communication is normal, J5, U100 is false welding, even welding Was the multimeter diode profile measurement (here) can be measured on the J5 TX0, RX0 turn-on voltage of 0.7 V (red pens and grounding, black pens and the test point.