宝马正时调整（BMW is adjusting）.docVIP

下载本文档

3
0
约 19页
2017-07-15 发布于河南
举报
版权申诉

宝马正时调整（BMW is adjusting）.doc

1、有哪些信誉好的足球投注网站（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

宝马正时调整（BMW is adjusting）

宝马正时调整（BMW is adjusting） How to adjust the author: auto repair special tool 12, 525i / 528i (E28) (engine no. 25 6E A, 28 6E C) (1981-1987); 530i / 535i (E34) (engine no. : 306k A, 34 6E C, 34 6K B) (1981-1993) (1) timing of valve timing 1. The engine stops at position 1 on the first cylinder. 2. Vertical vertical pair of camshaft sprockets (see FIG. 2). The camshaft sprocket is positioned in position 3. Remove tension plug 4. Note: ce4 is compressed by a strong spring. Remove the camshaft sprocket. As shown in figure 2-2-88. 13. 530i / 540i V8 (E34) (engine no. : 308s 1,408s 1) (1992-1996); 730i / 740I (E32) (engine no. 30 8S 1,408s 1) (1992-1994) (1) timing of valve timing 1. The engine stops on the first cylinder. 2. Insert flywheel timing pin 1. Tool number 11, 300. 3. Ensure that the first cylinder camshaft Angle 2 is opposite. 4. Make sure the camshaft sprocket arrow 3 up. 5. Install camshaft alignment tool 4. Tool number 11, 2, 441/442/443/444/445. 6. Before tightening the camshaft sprocket bolt, give the timing chain pretension. Use the tool 11, 3390 (see figure 5). As shown in figure 2-2-89. 14, 535I (E39) (engine no. 358s 1 (M62)) (1996-2000); 735I (E38) (engine no. 358s 1 (M62)) (1996-2000) (1) timing of valve timing Disassemble/install the timing chain needs: · remove the oil pan. 2. The engine stops on the first cylinder. 3. Insert the flywheel timing pin 1. Make sure the first cylinder has a convex Angle of two opposite. 5. Ensure that the sensor body is labeled at position 3. 6. Install camshaft alignment tool 4. 7. Use wrench 5 to prevent the camshaft rotation in the diagram position. 8. The secondary tensioner can be locked with tools 6. 9. Install the chains exhaust camshaft sprockets in the following order: · ensure that the threaded hole is at the center of the groove. · loosen the secondary tensioner. Install the exhaust camshaft sprocket bolts 7 (dont screw up). 10. Install the air inlet camshaft sprockets with chains in the following order: ·