大厦矿棉板吊顶施工工艺.docVIP

大厦矿棉板吊顶施工工艺 大厦矿棉板吊顶施工工艺提要：安装吊筋：根据施工图纸要求吊筋位置，安装吊筋预埋件（角铁），刷防锈漆，吊杆采用直径为φ8的钢筋制作，吊点间距900-1200mm 源自计划范文 大厦矿棉板吊顶施工工艺 1、施工工艺流程 基层清理--基层弹线--安装吊筋--安装主龙骨--安装次龙骨--机电隐检/龙骨隐检--矿棉板安装--成品保护--竣工验收 2、技术措施： 弹线：根据吊顶设计标高弹吊顶线作为安装的标准线。 安装吊筋：根据施工图纸要求吊筋位置，安装吊筋预埋件（角铁），刷防锈漆，吊杆采用直径为φ8的钢筋制作，吊点间距900-1200mm。安装时上端与预埋件焊接，下端套丝后与吊件连接，安装完毕的吊杆端头外露长度不小于3mm，。 安装主龙骨：采用Uc38龙骨，吊顶主龙骨间距为900-1200mm。安装主龙骨时，应将主龙骨吊挂件连接在主龙骨上，拧紧螺丝。 安装次龙骨：配套次龙骨选用T型烤漆龙骨，间距为600mm，将次龙骨通过挂件吊挂在大龙骨上。 安装边龙骨：采用L型边龙骨，与墙体用膨胀管自攻螺钉固定，固定间距200mm。 安装加强龙骨：龙骨安装时，在灯具和封口的周遍加设T型加强龙骨。 隐蔽检查：在水电安装、调试、打压完毕后，应对龙骨进行隐蔽检查，合格后方可进入下一道工序。 安装饰面板：矿棉板选用600*600mm的矿棉板，安装采用明装龙骨形式，矿棉板直接搭在T型烤漆龙骨上即可。随安装随时安装配套的小龙骨安装时工人必须带白手套，以防污染。 源自计划范文 daily morning exercises or class-break setting-up exercise and discipline inspection and appraisal of public signs;2, daily cleaning and inspection;3, the daily student school appearance, dress, wearing school card check;4, the daily duty guide to the leadership class discipline three rounds.Weekly moral education work:L, the flag raising ceremony and the national flag speech under the flag raising ceremony held on Monday;2, every week a class meeting, the meeting;3, every week two exercises, cleaning and hygiene, behavior norms, attendance situation published cloth appraisal, and the issue of the code of conduct;;4, weekly work week.Monthly moral education work:1, at least once a month, the theme of education activities, to patriotism education, behavior norms of education as the focus, combined with major retreat day.2, the monthly class quantization assessment and class teacher assessment, selection of behavior for the standard model class.Moral education in each term:1, at the end of each semester to form three good student, outstanding student cadres, civilized student.2, at least once a semester, parents will be.,Student etiquette conventionA, the school leavers1, dress neatly to wear school card, step posture correct, full of spirit; cycling of the same students, at the school gat