dd-wrt挂U盘，装lighttpd、ftp、php、mysql、miniupnpc、lynx、bo-blog，中继穿透外网.docVIP

dd-wrt挂U盘，装lighttpd、ftp、php、mysql、miniupnpc、lynx、bo-blog，中继穿透外网 dd-wrt挂U盘，装lighttpd、ftp、php、mysql、miniupnpc、lynx、bo-blog，中继穿透外网 测试平台：comfast cwr54g,刷DD-WRT v24-sp2 (02/23/10) mega作者：一剑 1.初始化后开始：(以下离开每一个页面前都要save)Administration-Management-Language:Chinese simplifiedEnable Info Site:DisableSetup-Basic Setup-Local IP Address:Time Zone:UTC+8Summer Time (DST):noneServer IP/Name:Services-Services-SSHd:EnableUSB-Core USB Support:EnableUSB 1.1 Support (UHCI):EnableUSB 1.1 Support (OHCI):EnableUSB Storage Support:Enableext2 / ext3 File System Support:EnableNAS-ProFTPD:EnableAllow Write:EnableNAT / QoS-UPnP-UPnP Service:EnableClear port forwards at startup:EnableAdministration-Management-Remote Access-Web GUI Management:EnableSSH Management:EnableTelnet Management:EnableJFFS2 Support:EnableClean JFFS2:Enable,Apply　　　　　　　　Commands-save firewall:(本案直接关掉了防火墙)iptables -I INPUT -p udp --dport 8081 -j ACCEPTiptables -I INPUT -p tcp --dport 8081 -j ACCEPT# iptables -I INPUT 1 -p tcp --dport 21 -j logaccept 2.挂U盘(注意，经测试，不能打开usb 2.0支持，否则失败，BCM5354本身集成了usb2.0支持的啊，还是供电不足？)PartitionManager v9.0，以管理员身份运行，格式化U盘为EXT2，插入U盘到dd-wrt上添加启动命令组Administration-Commands-Save Startup:umount /jffsumount /mntmount /dev/scsi/host0/bus0/target0/lun0/part1 /jffsmount /dev/mtdblock/4 /mnt重启路由器,-状态-路由器-空间使用，看到如下信息就成功了:JFFS21,888.35 MB / 1,888.33 MBwin7添加telnet功能后，ms-dos:c:\telnet root@DD-WRT:~# mkdir /jffs/opt启动命令组追加一条:mount -o bind /jffs/opt /opt重启,# mount 命令可查看挂载成功 3.测试ftp可用成功，但看不到文件，telnet进去后建立一个目录mkdir /mnt/xxx,刷新ftp窗口就看到了，删掉rm -R /mnt/xxx启动命令组追加一条:(ftp指向网站，该目录还不存在，为后面网站备用)mount -o bind /jffs/opt/share/www /mnt 4.安装optware dd-wrt：(所有支持软件参考/feeds/optware/ddwrt/cross/stable/)配置路由器，中继或客户端上网telnet root@DD-WRT:/# cd /jffsroot@DD-WRT:/jffs# dmesg (查看U盘加载信息)root@DD-WRT:/jffs# df -h (查看分区容量)root@DD-WRT:/jffs# du -h (查看目录大小)root@DD-WRT:/jffs# ls -lroot@DD-WRT:/jffs# wget http://www.3iii.dk/linux/optware/optware-install-ddwrt.sh -O - | tr -d \r /tmp/optware