HY-JK02-M 5轴运动控制卡使用说明书.docVIP

下载本文档

11
0
约3.12千字
约 13页
2019-02-12 发布于江西
举报
版权申诉

HY-JK02-M 5轴运动控制卡使用说明书.doc

1、有哪些信誉好的足球投注网站（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

HY-JK02-M 5-axis interface board manual Thank you for choosing our products，For your use of NC products better and faster，Please read this manual ?Features：Features 1: The maximum matching 5-axis stepper motor driver 2: The two-stage signal processing, signal transmission smooth, powerful anti-jamming 3:5 input interface to define the emergency stop, limit, points in the knife, etc.4: relay output control interface, can be accessed by the spindle motor or the air pump, water pump, etc5: five-axis job LED display, visual display products, working condition Electrical performance (Tj = 25 ℃ ambient temperature when): Input Power 5V DC power supply or computer USB to take power Work axis stepper Received the highest 5-axis independent driving Drive Pulse + direction + enable signal. Weight About 200 grams. Interface definition table: Waveform and timing Power output interface function Interface, detailed drawing marked In the test machine, note the following before 1, note that using the 5V power supply 2, determine the stepper driver works (Model0) 3, to determine the drive wiring step Second, the definition of the pin 1 is defined as parallel control： PIN9 PIN1 PIN2 PIN14 PIN16 PIN3 PIN7 PIN8 PIN6 PIN5 PIN4 PIN17 Spindle motor enabled X step X dir Y step Y dir Z step Z dir A step A dir B step B dir 2 hand control is defined as follows 1 ~ PIN15computer-15P interfaces and benchmarks within the Digital ID) P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 B step B dir A dir Z step Y step X step X dir enabled 5V/VDD 5V/GND A step Z dir Y dir enabled enabled 3 The limit is defined as 1 to 5 X -Limit Y- Limit Z- Limit A- Limit 急停 PLT-P10 PLT-P11 PLT-P12 PLT-P13 PLT-P15 5V 1A power supply, please take more than switching power supplies, power input received indicated on the map interface Spindle motor control is controlled via the parallel port PIN1. Spindle motor voltage must comply with the supply voltage range. Three MACH software to use Figure 1 Figure 1, open