有哪些信誉好的足球投注网站- 1、有哪些信誉好的足球投注网站（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
- 2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击 这里二次下载。
- 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
- 4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
- 5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
- 6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 7、VIP文档为合作方或网友上传，每下载1次， 网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
7-1焊点质量评定及IPC-A-610C（D）介绍
焊点质量评定 及 IPC-A-610C（D）介绍 8 Surface Mount Assemblies 8.1 Staking Adhesive Target Condition - Class 1,2,3 8.2.1.1 Chip Components – Bottom Only Terminations, Side Overhang (A) Target Condition - Class 1,2,3 ? No side overhang. Acceptable - Class 1,2 ? Side overhang (A) is less than or equal to 50% width of component termination area (W) or 50% width of land (P), whichever is less. Acceptable - Class 3 ? Side overhang (A) is less than or equal to 25% width of component termination area (W) or 25% width of land (P), whichever is less. Defect - Class 1,2 ? Side overhang (A) is greater than 50% component termination width (W) or 50% land width (P), whichever is less. Defect - Class 3 ? Side overhang (A) is greater than 25% component termination width (W) or 25% land width (P), whichever is less. 8.2.1.2 Chip Components – Bottom Only Terminations, End Overhang (B) Defect - Class 1,2,3 ? End overhang (B) in Y axis is not permitted. 8.2.1.3 Chip Components – Bottom Only Terminations, End Joint Width (C) Target Condition - Class 1,2,3 ? End joint width (C) is equal to the width of the component termination (W) or width of land (P), whichever is less. Acceptable - Class 1,2 ? Minimum end joint width (C) is 50% width of component termination (W) or 50% width of land (P), whichever is less. Acceptable - Class 3 ? Minimum end joint width (C) is 75% width of component termination (W) or 75% width of land (P), whichever is less. Defect - Class 1,2 ? End joint width (C) is less than 50% width of component termination (W) or less than 50% width of land (P), whichever is less. Defect - Class 3 ? End joint width (C) is less than 75% width of component termination (W) or less than 75% width of land (P), whichever is less. 8.2.1.4 Chip Components – Bottom Only Terminations, Side Joint Length (D) Target Condition - Class 1,2,3 ? Side joint length (D) equals component termination length(L). Acceptable - Class 1,2,3 ? Any side joint length (D) is acceptable if all other solder requiremen
文档评论（0）