胶囊填充机原理（Capsule filling machine principle）.docVIP

下载本文档

28
0
约2.25万字
约 25页
2017-09-02 发布于河南
举报
版权申诉

胶囊填充机原理（Capsule filling machine principle）.doc

1、有哪些信誉好的足球投注网站（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

胶囊填充机原理（Capsule filling machine principle）

胶囊填充机原理（Capsule filling machine principle） 2) check that all safety settings are properly equipped and properly adjusted. 3) in the absence of capsules and powder under the conditions, with the hand wheel in accordance with the direction of the machine rotation 1-3. After its normal, the capsule and powder are respectively loaded into the capsule bucket, and the powder filled in the height of the powder bucket is lower than the highest 60mm of the container. At the same time, there should be more than half of the powder in the measuring and distribution room. 4) adjust the filling rod and insert the depth of the metering disk. 5) after all adjustment, press the main engine to move, move normally, and then start the switch for automatic operation. 6) the speed adjustment is performed at the main motor operation. 1.3.3 operation 1) check the signal lamp is normal, close the glass machine door. Switch the main power switch SB10 from OFF to ON position, the indicator light HL4 and HL5 are bright, and the frequency converter is also displayed accordingly. 2) first start the vacuum pump motor M2, press the vacuum start switch SB1, the indicator light HL1, HL4 dark, the vacuum pump motor running. The first boot to check the direction of motor rotation, if the direction is wrong, to change the power phase sequence. 3) the running state of the main motor is divided into two states: inching operation and continuous operation. A. start the main motor M1, press the host start switch SB3, the indicator light HL3, HL5 dark, the main motor running. When the vacuum pump motor does not start or the machine opens the door, the main motor can not start, only wait for electric operation B. the main motor running point, press the host point action switch SB6, the indicator light HL3, or dark, the main power Machine operation, release the host point, move SB6, the indicator light HL5, HL3 dark, the main motor stops, the first boot should first.. Point running, the rear can run continuous