GLM – ASME Purchasing Requirements Page 1 （全球语言监测机构-第1页ASME采购需求）.pdfVIP

下载本文档

16
0
约 2页
2017-09-02 发布于浙江
举报
版权申诉

GLM – ASME Purchasing Requirements Page 1 （全球语言监测机构-第1页ASME采购需求）.pdf

1、有哪些信誉好的足球投注网站（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

GLM – ASME Purchasing Requirements Page 1 （全球语言监测机构-第1页ASME采购需求）

PURCHASING TERMS AND CONDITIONS GLM INDUSTRIES L.P. – REQUIREMENTS FOR MATERIALS PROCURED FOR THE CONSTRUCTION OF ASME PIPING AND PRESSURE EQUIPMENT The below listed information defines the minimum requirements for specific groups and forms of material and welding consumables commonly used at GLM Industries L.P. for pressure equipment constructed to the following codes: • ASME Section VIII – Division 1 – 2010 (2011a); ASME B31.3-2012; ASME B31.1-2012; CSA B51-0 To define the requirements for a specific component, select the appropriate form (plate, head, re-pad, fitting, etc.) and the desired material from the table(s) below. For components and materials not defined below, please contact the engineering department for specific requirements. REQUIREMENTS FOR ALL MATERIALS AND COMPONENTS: The following is required for all materials and components: • Material Test Report (MTR) required • Heat #/Lot # and code material markings are required (Vendor marking system must be accepted by GLM Industries prior to order confirmation) • All fittings must be registered with ABSA and hold a valid CRN # in the province of Alberta (if final installation will be in another province, the fitting design must be registered in that province). PLATE Material(s) Requirements SA-36 - Material complies with specification ASME Section II – 2010 (2011a) SA-240-304(L) SA-240-316(L) SA-516-70N - Material complies with specification ASME Section II – 2010 (2011a) - Impact tested at -50° F (30 ft.lbs Min. Average/20 ft.lbs Minimum, Single Test – Longitudinal) FORMED PLATE AND/OR PRE-FABRICATED COMPONENTS (HEADS, ROLLED PLATE, RE-PADS, WEAR PLATES, MANWAYS) Material(s)