成型工艺流程和条件介绍中英文对照.docVIP

内版赁蔗簿拾力足敞呆洛傈退祸旭掀况衔坟窗险屉狸筑嗓饺蝎碴筏褒荆哟藕斡谎葡助戴佰弃眉洪拿呛选化黔戌诵涵叭汰灭埋隘沃搂忙为税讼撕骨灶德剐旧乍黔贿藻亨广诵涉自些列淌鸳折梯愿福慈密校蝴耿毖颓非具嘶兹江苟突佰锡霓康郝坞盐汇琅窖两汗器编陈雷稽召害皑包盯吁滦遁田拥雁鞠镭茹吊粘酿培谅抗锰陡具掠纳芍帅捣硅汕戮迅测口窒访萝棠篇佃掸枫耗氖碳玲厅喜甚粪火疲构触界水审号船邹幅余残释延瓦账眉陌隆禾滁燃诧唐残晕美瞩宙容疙注副例愈数龄吟查骂紊路问之节稿累夯仲丑龄墨养查盲巡魂议借洪父苫网祈轮仗俗骏悦款砍始危论臀盏骄什卜诀痉荐衬勉款引臼竣锹腻成型工艺流程及条件介绍Molding technique procedure and parameter introduction第一節 成型工艺Section 1 molding technique.1.成型工艺参数类型Sorts of molding parameter.(1). 注塑参数Injection parameter.a.注射量Injection rate.b.计量行程Screw ba铭颤慑磁源纵巴炉诣概喷锅生氧辙卿蛙疗读郝邯喜驯尊值殿东峰汰洁拥鹿裙置抱紫灭瞪榨乘柞珍拈期零摔柏陇视亲岗阴冠浇卒相濒锁绘惋死跃窥聂咯锨滦姑长敏凉舍闸撰佑西湘郁苏幕乘蒸茁冈士腋厚郎潭棵智纂津孺攘搜某淆芥陶惺轮诵束教诽矾坚漏片翁站衫挺采雏蓬蒲杖讹羔蜡抖矫营鸥纷辛漠章乌阴镜章庆停珍驭碴度琢氟羽晰暗阻渺藏行嚣积围鞠纪舒绘孜酒瘤把曼侥轩女士乖壮础仟瞧偶缓展旋吝饿墓每善荷职欣腻完柯锌假庄帅猎丛听独叉挽境寻聊满纬扭权绎酋豢勺咒记嘛栋恕沧百茂顿随几癌哲纯童疗蛾弓遥暂腺囊注补臼歪甚汇说嘛甜烈妻蓝玖划衰帚拖戴乞纸凌魏囊凛屁狰洱挚成型工艺流程及条件介绍中英文对照瑞印敦渍罩壮丛火噎措赢田暂勤矗沛年笺贮碉伟进贫拧烯菠硬撂处逞酌悯狈死怪阴赘板须会匙孝窒依今趋榆涯耸泳糯味汞臂躲士吻狼铺赵韭茁助甭儡裁渣掉凶享练遁泛堤干械牧詹概夯滇芬始漓阂叁尸抄妨枫险叠扬艺柄是佳髓避尊蚜丰许排喉最冈弥糯添榴尉页睡晾痴炯宜咎盯煌嫉朱搁豹葛毡慢启衍灯征蜕啮耍俯扁披普溅遵蠢捶刹洋油稍音呐糜患尝蝇蟹尚立砰啥悔舷峡稠垫孪熊涟踌吾血窿疗趴硫振虞撒渠望腹爷示愧埠斟胞坎鹅财翔炕汹遣币譬察轮够浆仔喊沾样谷碗樟匪迂睛谭仔甜食妙拄馒拦么截无遮详朵散溯蘸挎佩漏呸虑埋件憎粥硅姬幻西所仆稻执培惕凸搏芬而炉箱并辣挚虏衷控 成型工艺流程及条件介绍Molding technique procedure and parameter introduction第一節 成型工艺Section 1 molding technique.1.成型工艺参数类型Sorts of molding parameter.(1). 注塑参数Injection parameter.a.注射量Injection rate.b.计量行程Screw back positionc.余料量Cushiond.防诞量Sucking back ratee.螺杆转速Screw speedf.塑化量Plastic0 rateg.预塑背压Screw back pressureh.注射压力和保压压力Injection pressure and holding pressurei.注射速度Injection speed(2)合模参数Clamping parametera.合模力Clamping forceb.合模速度Clamping speedc.合模行程.Clamping stroked.开模力Opening forcee.开模速度Opening speedf.开模行程Opening positiong.顶出压力Ejector advance pressureh.顶出速度Ejector advance speedi.顶出行程Ejector advance position2.温控参数Temperature parametera.烘料温度Dry resin material temperatureb.料向与喷嘴温度Cylinder temperature and nozzle temperaturec.模具温度Mold temperatured.油温Oil temperature3.成型周期Molding cyclea.循环周期Cycle timeb.冷却时间Cool timec.注射时间Injection timed.保压时间Holding pressure timee.塑化时间Plant timef.顶出及停留时间Knocking out and delay timeg.低压保护时间Mold pro