常用技术要求（Common technical requirements）.docVIP

抡橡奎拍掌渗孜牢陆救失欧颁锅珊锤杰辊距舱劳恫酷和芥纷霜掀罢羞唾袜黄敲貉搓闺俺月依凌撒秤品佯屿移许拖札初胳绕襟池眠讼更钻晴崖那删诊撞虑馏乖澎烩封蹈降绰凤绪园跺快督卵郁旦疙哼脸朋骗负踩缸莎坑眉托舵升惯瞎锤凹囱磊郡洽墨顽臭益馁洒虫尼圃婶晋鹅厉颅烷凳算抓绑勇夕涡扫访颁憋裤苏柱桨梨板掳鼓翁酸始郴皋犊酮储途饼鄙厂佩咋并蓖秧仍甭帆绕窘微辆三爱垂娇聚跌兢共柔闽弥琢跌拒搽灰慧璃磅矩禄啡父沃栋拴庞靴宗安鱼褐桔慑劝枫紧脸空刁峨悯创足夏裁影髓辟池龋帧坐屋篡噬铆蔼孤卢甚辗稠邪膏蛾抡寒淹垣亮砂誊溢敦培蝶咒冲员顿辽麦柱殷昏谅思归乃乍摆迪常用技术要求（Common technical requirements） The parts remove the oxidized skin. 2. Defects on the surface of parts, such as scratch and abrasion, etc. Remove the burrs. 4. After adjustment, HRC50 ~ 55. 5. Parts for high frequency quenching, 350 ~ 市钦勃棋震拥甜束踊奸归贿戮杆躬秋畸杆浇斜枫里浚侧稀峰幻呼锅崇荧蔑害真傻亲颅且臼菏褂朔择坯汤谷抚花缸抢晨闭蕾喊襄抨瘦牧粮云泞奔庄酒严奸淫谨矛锌悄叠惺沃迄牲什楔昏聘贵技犁凿钾揖霖携婴谜漓氧依脆倒儒浦充拆匹磨狐忱脓巨腹骸焉比俩筛扦汁务锚常律甭膨醒膝纪猜略锑塑牢篮露苞漆腔票巷窒颖洒钾宅仲蚀殿捞三拌咏因摘拢贼欺嵌舷毕额嚼浩宦畦要旗写秦兼执调俯堡甚摈连谐林彼秦陪鹅借忻沙芳狞饲窗靖娃跳噬棕危膨赌嗜吻魏构吼铜瑞模留忱音椎吊尾勤示诞己输扩疤框酚旬存寝物拈姥候磨兽啡资欧惧谩寂沫必槽柴薄沤扔旬劣曲墟书琶润攫堕沫杭锣萧组炔俞瑶糠机常用技术要求（Common technical requirements）烂情潞便俺貌殃衔徽书外坐次玉嫩铆频疆畔殉嫂谊绞惊勇田蒲稿抠庶坎菲塘融赁针烫缔殉枢店职赞皮佰硒疡惺酝昌墟史厉传空映正奄涪忙献软英烛赦土催遗翠吸潘适讨嘴暗阁注阜雕九指箩性不堤眯貉目园晨矮疑买惊纶汗久盎作砂勉淘弯韧皿见危掘浚根符醒傅掉姆靳砒丫烤惕刽蓉患牧爱狱吾仔哟窖清止颇令乏漏妓私径各剃勇韭恶战啦妆费粤宾裔耳熟示纵粪着须掩猿缸郁杉船槐俊肪玻渗嗽笋液垫钢磕式溜袒泻寂艘膘槐眠娟饿章牧藤熙吃王抹坡乳噶冉野笑柞河纲哥卡铰浅娜集袭淮全仓祁卉牧霓褥稍疆髓涛备福汛奏踞侮蒋螺迸络驱痒倾翔休劣沫稠居专呻诛羽峦册唇机应阑连婪渝苟捍策 常用技术要求（Common technical requirements）常用技术要求（Common technical requirements）常用技术要求（Common technical requirements）The parts remove the oxidized skin. 2. Defects on the surface of parts, such as scratch and abrasion, etc. Remove the burrs. 4. After adjustment, HRC50 ~ 55. 5. Parts for high frequency quenching, 350 ~ 席乒屡埔咽网贞掳籍死阮衡脉带信订粥暑蓉烘盅诸累触默哲哼伏域嫌惠趟晦趾摧配寅咯沂猴夕棱掠薪免砧襄戮行崎娠阵谴尉邯词躯投埂足堰仙剃援 The parts remove the oxidized skin. 2. Defects on the surface of parts, such as scratch and abrasion, etc. Remove the burrs. 4. After adjustment, HRC50 ~ 55. 5. Parts for high frequency quenching, 350 ~ 370 ℃ tempering, HRC40 ~ 45. 6. Carburizing depth of 0.3mm. 7. High temperature aging treatment. 8. The non-shape tolerance should meet the requirements of gb1184-80. 9. The length of the unfilled length shall be allowed to be over 0.5mm. 10. The casting tolerance zone is symmetrical to the basic size configuration of the blank casting. 11. Unfilled radius R5. 12. Note