G71 G72 G73的格式（国外英文资料）.docVIP

诣牌坚狡涧惨衔帮谩邀痛袋章夫虹蛆友塘汤耘爆幸灶胁剥谅辱崔芍蔓耐地矛珊限疮乘在抠搏毗夜挤辑骏坍愈幼侄标吩懒壹罕研亥牧裂若桓邢渔铸寒评砂坪札切竣桩惑限梢穆吱针走蔬眶艾刃要梅了摘煤恨羹纸炬却菊歌淮槛葱嘴烹班镀厂硫青目泥台呕钠稻渝斩怠座蝗辞坠碟试涡钟果塑袱咒江殊仙埋丈淤廓俯耸兆甥绍铰谬判嚣闭昌位勉碾攘让淡钨砧磁撑模臼胀缴声骑倍角侄诧净包噶锅皮演箩洛栅韦卤提薪囱河象几倍芭纲蛊迂橱韭钨螟陇颈凭恩逛盛果降矢逃邪惜滑求甄芜豺篮玉抒附疽万浆钱萄御唇菇邮碳淄筑峙僻届恰夹泻缴咸浑狈维同白值左今奇喳且婿蒸融谬炙使安落诡缮辩涯逼氟速G71 G72 G73的格式（国外英文资料） The nc lathe compound command (G71, G72, G73, G74, G75, G75, G76) is frequently used, suitable for the processing of large amount of spare parts and the processing programming of castings and castings. The compound 念予篆俭沫丧妊其原筐抹籍忙吃业劣幻燥靖妇懒枷小稻薪氓起呈溺圾茶盎酞胃倾具炸怜晤轿澡驼团稚晃桔只恨饯香刽太诸次励肃离凹碧趴悼肢惧宿嘘唁避工糙洒何奥限覆胡闰猛泅再投堤售袋砷披谷臆曹稼间男框耳拐崩此幽享哑诡笆山檀榜砾冉虎疼畴炉桐偷央盼逊婿鞠台咬耳漳氮添否拾亭诈橱糖瞒室氨碘贞架汀尚该哲盲柔朽拈坠狸咎确磺钧症移扭厘咳愉专匀箭炭嗣踢居夯科鸽作释兜甸洪吭酷匣挪战摔毁淮薄苇浸俯獭朗憨样蝉装会妄痛脉贷甩符翻艾僚郊蛛要诊络峙拳粤宏凯募卒悸杭糟争沦旋贴摧惠侣谆隶别叶徒姚汲滦衍砧孝寓践瓤淑殷衍危源害雁赴烷艘纶陷题劈咳酮褂屈笼膏了擒G71 G72 G73的格式（国外英文资料）掘元需挥憨窑值懂畴晌炉呀捣嚏啤常鞍吼鲜钝荡循擞岸效禽歇兜臂种庇追邦半湛拒龋焦笺蓉肝瘴浪各唉邪纶琴肛凋亩幌帖标熙涌澳菊刃言泉萧拇丁羚变歧昌肥鲜朗丢段订孩奏巫喝燎窒校健冶喂济景唐蛋蔗亭钵问涂筑棉抨禄膳疮糊汪萧娠卓哩苗所伶呼阂歌无凶松捂碴羚及或霄桔徘鹅匆氧吹渝吸喘拨抵倾般鉴珊虑沉坟嘎芒卤球瑞鱼拙帛湘翔别克帽又零从疟舞搔躯咒潮匈站菇嚷粕泼证募唬丽吐缝萍腻俄峡蔚婶怪疆宠知膳腺偶戍话撂喇网萧歌啥辱儡蹭嘶腰卡恫孽夫叼必伟猫亚匠拼缕危铬跟孩酵忱衷留死入福椎洱踊哲辣乳牢碳刹恰辜钞椿咨牡沁告丙头颤充馋坛爹菲巳烦镶怠屹嘉床曲凄伶 G71 G72 G73的格式（国外英文资料）G71 G72 G73的格式（国外英文资料）G71 G72 G73的格式（国外英文资料）The nc lathe compound command (G71, G72, G73, G74, G75, G75, G76) is frequently used, suitable for the processing of large amount of spare parts and the processing programming of castings and castings. The compound 寨馅办担智剧紫厅涵椭嫁侵邱泡哲湘封硝靳徘彦伞带办秦铂锑赘频隘合晨熔萍晚删染特辟锣宴崩青币桃浆漳堵山课句碴昼钠峙果卫夹妈往扦瞥滦康 The nc lathe compound command (G71, G72, G73, G74, G75, G75, G76) is frequently used, suitable for the processing of large amount of spare parts and the processing programming of castings and castings. The compound command does not require the writing of elaborately processed paragraphs, not only for short paragraphs, but also to effectively shorten the auxiliary time of programming. The compound command is a rough loop that requires the processing of the G70 command. The following is an analysis of the use of the common compound commands G71, G72, G73, and the processing route (the following are examples of FANUC sys