电焊工安全操作规程（七）.docVIP

电焊工安全操作规程（七） 电焊工安全操作规程（七）提要：电焊机应放在防雨和通风良好的地方，焊接现场不准堆放易燃、易爆物品，使用电焊机必须按规定穿戴防护用品 更多精品自报告 电焊工安全操作规程（七） 1、电焊机外壳，必须有良好的接零或接地保护，其电源的装拆应由电工进行。电焊机的一次与二次绕组之间，绕组与铁芯之间，绕组、引线与外壳之间，绝缘电阻均不得低于兆欧。 2、电焊机应放在防雨和通风良好的地方，焊接现场不准堆放易燃、易爆物品，使用电焊机必须按规定穿戴防护用品。 3、交流弧焊机一次电源线长度应不大于5米，电焊机二次线电缆长度应不大于30米。 4、焊钳与把线必须绝缘良好、连接牢固，更换焊条应戴手套。在潮湿地点工作，应站在绝缘胶板或木板上。 5、严禁在带压力的容器或管道上施焊，焊接带电的设备必须先切断电源。 6、焊接贮存过易燃、易爆、有毒物品的容器或管道，必须先清除干净，并将所有孔口打开。 7、在密闭金属容器内施焊时，容器必须可靠接地、通风良好，并应有人监护。严禁往容器内输入氧气。 8、焊接预热工件时，应有石棉布或挡板等隔热措施。 9、把线、地线，禁止与钢丝绳接触，更不得用钢丝绳或机电设备代替零线。所有地线接头必须连接牢固。 10、更换场地移动把线时，应切断电源，并不得手持把线爬梯登高。 11、清除焊渣采用电弧气刨清根时，应戴防护眼镜或面罩，防止铁渣飞溅伤人。 12、雷雨时，应停止露天焊接作业;更换场地移动把线应切断电源。 13、必须在易燃易爆气体或液体扩散区施焊时，应经有关部门检试许可后，方可施焊。 14、电焊着火时，应先切断焊机电源，再用二氧化碳、1211于粉等灭火器灭火，禁止使用泡沫灭火器。 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students ideological quality, psycholo