机床简单故障解答精要.ppt

下载文档 降价啦

52
0
约1.13万字
约 92页
2017-05-06 发布于湖北
举报
版权申诉
保障服务

机床简单故障解答精要.ppt

1、本文档共92页，可阅读全部内容。
2、有哪些信誉好的足球投注网站（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

机床简单故障解答精要

报警信息报警信息报警信息报警信息报警信息报警信息报警信息报警信息报警信息 00 EMERGENCY STOP BUTTON 01 CHARGING DOOR OPEN 02 DRIVES NOT READY 03 EXCESS TEMPERATURE DRIVES 04 SAFETY RELAY/PROTECT.DOOR 05 AXIS LIMIT SWITCH 06 ETC ERROR MACHINE PARAMETER 07 TIME OUT SPINDLE 08 PASS OVER REFERENCE 09 ERROR AXIS POSITIONING 10 STAND BY 11 ERROR CHANGER TC58 12 ERROR CHANGER 13 TIME OUT HYDRAULIC EQUIPMENT 14 ERROR MACHINE PARAMETERS 15 TOOL CALLED FROM MAGAZINE 16 TIME OUT SPINDLE POSITIONING 17 TC NOT IN HOME POSITION 18 TIME OUT DRAW BAR 19 TIME OUT TOOL CHANGER DOOR 20 TOOL CLAMPED INCORRECT 21 ROBOT ERROR 22 IV.AXIS:PRESSURE SWITCH 23 V.AXIS:PRESSURE SWITCH 24 IV.AXIS:FAULT POSITION 25 V.AXIS:FAULT POSITION 26 TOOL NOT CORRECT IN MAG. 27 ERROR MAGAZINE POSITIONING 28 SPINDLE OVERLOAD 29 PLC ERROR MODULE 9XXX 30 M-FUNCTION NOT ALLOWED 32 COOLANT SYSTEM ERROR 33 SPINDLE SPEED CONTROL MON. 34 TOUCH PROBE ACTIVE 35 EMPTYING SPINDLE 36 OVERLOAD:AUX. EQUIPMENT 37 EXCESS TEMP. SPINDLE MOTOR 38 ERROR SPINDLE LUBRICATION 39 SPINDLE I2T CONTROL 46 ERROR SPINDLE COOLANT 47 PRELUBRICATION SPINDLE ACTIVE 48 EXCESS TEMPERATURE SPINDLE 49 TC WITHOUT POS. ROT. AXIS? 60 CLOSE PROTECTION DOOR 61 OPEN/CLOSE PROTECTION DOOR 62 WAIT PLEASE 63 LUBRICATE THE MACHINE 64 LUBRICATION SOON NECESSARY 65 PERM. BUTTON/PROT.DOOR 66 SET-UP MODE 67 SET-UP MODE EXTENDED 68 INSERT TOOL CORRECT IN MAG. 69 COOLANT SWITCHED OFF 70 FEED OVERRIDE=0% 71 CLOSE CHARGING DOOR 72 TOOL CHANGE IN ACTION 73 CHIP CONVEYOR INACTIVE 75 M69 PROGRAMMED 76 COMMUNICATION ERROR 77 WARM UP SPINDLE ACTIVE 78 CHECK SPINDLE LUBRICATION 79 PRELUBRICATION SPINDLE ACTIVE 80 ERROR SPINDLE COOLANT 81 EXCESS TEMPERATURE SPINDLE 82 ETC IN Y DIRECTION INACTIVE 83 ETC IN Z DIRECTION INACTIVE 84 ETC INACTIVE 85 TEMPERATURE SENSOR DAMAGED 86 EXCESS TEMP. SPINDLE MOTOR 87 ROBOT NOT READY 91 TC DOOR -OPEN CLOSE- 92 DRAW BAR -OPEN CLOSE- 93 Z AXIS -PLUS MINUS- 94 Y AXIS -PLUS MINUS- 95 MAG. POSITIONING -CW CCW- 96 WITHOUT FUNCTION 97