Metallurgical investigation of failure of coal mill drag chain pin.pdfVIP

下载本文档

7
0
约1.9万字
约 7页
2017-04-13 发布于江苏
举报
版权申诉

Metallurgical investigation of failure of coal mill drag chain pin.pdf

1、有哪些信誉好的足球投注网站（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

Metallurgical investigation of failure of coal mill drag chain pin

Materials and Design 30 (2009) 2623–2629Contents lists available at ScienceDirect Materials and Design journal homepage: www.elsevier .com/locate /matdesTechnical Report Metallurgical investigation of failure of coal mill drag chain pin S.G. Sapate *, V.K. Didolkar Department of Metallurgical and Materials Engineering, Visvesvaraya National Institute of Technology (VNIT), South Ambazari Road, Nagpur 440011, Maharashtra, India a r t i c l e i n f o a b s t r a c tArticle history: Received 6 June 2008 Accepted 5 November 2008 Available online 30 November3069/$ - see front matter 2008 Elsevier Ltd. A doi:10.1016/j.matdes.2008.11.021 * Corresponding author. Tel.: +91 712 2222828; fax E-mail address: sgsapate@ (S.G. Sapate)The present paper reports metallurgical investigation of fractured connecting pins of drag chain convey- ors used for coal conveying from raw coal hopper to grave gate in coal mill of a cement plant. The failure analysis of two fractured pins was carried out; the location of the fracture was near the end of the pins. Both the failed pins had reduced cross section in the immediate vicinity of the fractured surface. The chemical composition of the pins confirmed to En-19 specifications. The hardness and metallographic studies indicated that the pins were induction hardened at the surface whereas the core of the pins had tempered martensitic microstructure. The visual observations of the failed pins confirmed entrap- ment of fine to heavy coarse coal particles on the pin surface causing mild to severe polishing wear with subsequent reduction in the cross section. The metallographic studies showed non-uniformity in the induction hardening and undesirable coarse martensitic microstructure at the core. The analysis of the fractured surface and fractographic studies by SEM indicated fatigue fracture due to bending stresses and mild to moderate torsional stresses. The proper induction hardening to ensure required case depth and use of En-24 steel f