Gel Casting of 316L Stainless Steel Powder Through Mold DIS Proces.pdfVIP

下载本文档

7
0
约2.28万字
约 7页
2017-04-13 发布于江苏
举报
版权申诉

Gel Casting of 316L Stainless Steel Powder Through Mold DIS Proces.pdf

1、有哪些信誉好的足球投注网站（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

Gel Casting of 316L Stainless Steel Powder Through Mold DIS Proces

TSINGHUA SCIENCE AND TECHNOLOGY ISSN 1007-0214 37/38 pp216-222 Volume 14, Number S1, June 2009 Gel Casting of 316L Stainless Steel Powder Through Mold DIS Process* WANG Fei (王霏), JIANG Kaiyong (江开勇)**, XU Xipeng (徐西鹏) College of Mechanical Engineering and Automation, Huaqiao University, Quanzhou 362021, China Abstract: This paper presents the gel casting of metal powder by agar gelation through mold decomposed injection sculpture (DIS) process: verifying the feasibility and improving the processing parameters to pre- pare stable metal slurry and strong green body. The optimal processing parameters were achieved after in- vestigating the effects of these parameters such as temperature, agar content, dispersant concentration, and solid volume loading. The rheological behavior of metal slurry and the character of formed green body were also investigated. The mixture and dispersion mechanism of metal slurry as well as the consolidation forming and sintering technology of green body were studied based on analysis of experimental results. The results show that the optimal pH range is 8.5-9.5 with the grain size distribution of 2-30 μm and 55% solid suspension, which can be prepared by adding proper dispersant (Polyvinyl Alcohol). The agar and dispers- ant content has great effect on the properties of slurry. When 1.0 wt.% dispersant and 0.7 wt.% agar content (referred to dry solid) are adopted, stable metal slurry with viscosity less than 1 Pa ? s and green body with bending strength of 2.7 MPa are obtained. The sintered bodies with uniform structure, relative density of 90%, and yield strength of 150 MPa are prepared at 1300℃/30min in vacuum. This process can be applied in rapid prototyping of complex shape metal products such as rotor blades. Key words: rapid prototyping; mold decomposed injection sculpture (DIS); 316L stainless steel; agar; gel casting Introduction Decomposed injection sculpture (DIS) was not only additive (injection) but al