Creep–fatigue damage dissimilar metal welds of modified 9Cr–1Mo steel and 316L stainless steel.pdf

下载文档

3
0
约3.97万字
约 12页
2017-04-13 发布于江苏
举报
版权申诉
保障服务

Creep–fatigue damage dissimilar metal welds of modified 9Cr–1Mo steel and 316L stainless steel.pdf

1、本文档共12页，可阅读全部内容。
2、有哪些信誉好的足球投注网站（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

Creep–fatigue damage dissimilar metal welds of modified 9Cr–1Mo steel and 316L stainless steel

I/locate/ijfatigue International Journal of Fatigue 29 (2007) 1868–1879 Journalof FatigueCreep–fatigue damage for a structure with dissimilar metal welds of modified 9Cr–1Mo steel and 316L stainless steel Hyeong-Yeon Lee *, Se-Hwan Lee, Jong-Bum Kim, Jae-Han Lee Division of Mechanical Engineering, Korea Atomic Energy Research Institute, 150 Dukjin-dong, Yusong-gu, Daejeon 305-353, Republic of Korea Received 15 September 2006; received in revised form 1 February 2007; accepted 5 February 2007 Available online 20 February 2007Abstract A creep–fatigue test with a structural specimen made of Mod. 9Cr–1Mo steel and 316L stainless steel has been carried out and the test results were compared with those of the evaluations by the high temperature design codes of ASME subsection NH and RCC-MR to quantify the conservatism. A specimen with a diameter of 500 mm, height of 440 mm and thickness of 6.3 mm was subjected to creep– fatigue loads with two hours of a hold time at 600 C and a primary nominal stress of 30 MPa. The creep–fatigue behaviours of the dissimilar metal welds as well as the similar metal welds were investigated and the results of the test were compared with the evaluation results. Bimetallic (direct) transition metal joint and trimetallic transition metal joint for a dissimilar metal weld were employed for a specimen, and their behaviours under a creep–fatigue load were compared. The conservatism of the design codes on the creep–fatigue evaluation at the welded joints as well as at the base metal with an emphasis on Mod.9Cr–1Mo steel are highlighted through comparisons with the results from the observation and the evaluation. 2007 Elsevier Ltd. All rights reserved. Keywords: Creep–fatigue; Damage; Dissimilar metal weld; Mod.9Cr–1Mo steel; 316L stainless steel1. Introduction Modified 9Cr–1Mo steel (ASME Grade 91) has been widely used for a high temperature structure such as a steam generator, intermediate heat exchanger and second- ary piping of a liquid metal