IEC61850工程实施规范附录A逻辑节点类一致性要求(企业报批稿)..docVIP

IEC61850工程实施规范 附录A：逻辑节点类一致性要求 A.1逻辑节点零LLN0 属性名属性类型全称公用逻辑节点信息Mod INC Mode M 模式 Beh INS Behaviour M 行为 Health INS Health M 健康状态NamPlt LPL Name M 逻辑节点铭牌Loc SPS Local operation for complete logical device O 就地位置 OpTmh INS Operation time O 运行时间 控制 Diag SPC Run Diagnostics O 装置自检 LEDRs SPC LED reset O 复归LED MainEna SPC E 主保护软压板 MainEna2 SPC E 主保护2软压板 DISEna SPC E 距离保护软压板 RTOCEna SPC E 零序过流软压板 RETRIPEna SPC E 远跳投入软压板 CHARGEna SPC E 充电保护软压板 ROCEna SPC E 相电流保护软压板 AccelEna SPC E 双回线加速软压板 A.2 保护通道PSCH 属性名属性类型全称公用逻辑节点信息Mod INC Mode M 模式 Beh INS Behaviour M 行为 Health INS Health M 健康状态NamPlt LPL Name M 逻辑节点铭牌OpCntRs INC Resetable operation counter O 可复归的动作计数器状态信息 ProTx SPS Teleprotection signal transmitted M 纵联保护发信或远跳保护发信 ProRx SPS Teleprotection signal received M 纵联保护收信或远跳保护收信 Str ACD Carrier Send M 启动 Op ACT Operate M 动作CarRx ACT Carrier received after unblock logic O 解闭锁逻辑收信 LosOfGrd SPS Loss of guard O 监频消失 Echo ACT Echo signal from weak end infeed function O 弱馈回音信号 WeiOp ACT Operate signal from weak end infeed function O 弱馈动作信号 RvABlk ACT Block signal from current reversal function O 功率倒向闭锁信号 GrdRx SPS Guard Received O 监频收信 RemSig1Tx SPS Remote signal 1 received E 远传1RemSig1Rx SPS E 远传1 RemSig2Tx SPS Remote signal 2 received E 远传2RemSig2Rx SPS E 远传 PhSegPmsEna ACT Phase Segregated Permiss ive Signal Enable E 分相允许信号 Ch1Alm SPS Channel 1 alarm E 通道1告警 Ch2Alm SPS Channel 2 alarm E 通道2告警 ChFail SPS Channel failed E 通道中断 SynErr SPS Synchronization error E 同步出错 ChSw SPS Channel switched E 通道切换 ChNeedChk SPS Channel need check E 通道需检查 ChDlLong SPS Channel transmission delay too long E 通道传输延时过长 ChDlUnstd SPS Channel transmission delay unsteady E 通道传输延时不稳定 Ch1IDUnmach SPS Channel 1 ID unmatched E 通道1编号不匹配 Ch2IDUnmach SPS Channel 2 ID unmatched E 通道2编号不匹配 RemTrPers SPS Remote trip persistent E 远跳长期不复归 RemSig1Pers SPS Remote signal 1 persistent E 远传1长期有开入 RemSig2Pers SPS Remote signal 2 persistent E 远传2长期有开入