[常用英语词汇.pptVIP

常用英语词汇Sharlin前模/定模/母模 cavity (cavity 也叫模穴） 后模/动模/公模 core (core统称模芯,模仁） 枕位、穿插、碰穿 shut off 直径 diameter 圆角/半径radius 重叠 overlap 导向槽guiding slot (不动的部分） 倒扣 undercut 切线 tangent 脱模角度、拔模锥度draft angle 分模线/分型面 parting line=PL 行位分型线 slider PL 骨位 rib 槽 slot 段差 step 圆顶针ejector pin round 缩写是EP round 扁顶针ejector pin blade （blade原意是刀片，叶片） 平均胶位厚度The average plastic thickness 模镶件线core insert line 隧道行位Tunnel slider 锁模力 clamp force 绝缘 resist coating 相切半径 tangent radius 电镀夹片 racking tab 斜顶 lifter 内圈分型线 inside parting line demold 脱模 as per the issues above 上述问题 扣位 clip intersect [,int?sekt] vi. 相交，交叉 （两条直线或两个平面相交） vt. 横断，横切；贯穿 正段差是后模比前模小，逆段差就是前模比后模小。都用step 色粉 colorant 水口残留 Gate vestige EPE foam 珍珠棉 (Expand Aple Poly Ephylene) 损耗率 scrap rate scrap：废弃，残留 标准样板 master sample 限度样板 boundary sample 颜色限度样品color boundary sample 缺陷样板 defect sample 产品V/P切换压力为57.5MPa Pressure at V/P switchover is 57.5Mpa 模流分析 moldflow analysis 体积收缩 volumetric shrinkage at ejection 缩痕估算 sink marks estimate 总体变形 all effects deflection X.Y方向变形 deflection, all effects: X.Y component 蚀纹 texture ，graining 贴胶带 felt tape 吸塑包装 blister packaging 进胶方式 3 怕结合力不好，建议第一色做孔，增加结合力. We suggest add some holes on the first shot in order to increase the adhesion strength 4 为利于模具制作及简化分型面，建议箭头所指侧面减胶拔模到后模. We suggest the by arrow indicated side reduce material and making into the core in order to manufacture the tool easier and simplify the parting line. 5 建议上图中两个绿色孔侧面沿行位运动方向做脱模斜度 We suggest adding draft on 2 green sides along the moving direction of slider. 6 为了保证外观面，建议将PL面下移0.2MM。 Suggest lowering the PL 0.2MM to avoid the PL on the visible surface. 7 此绿色面没有出模角，建议以减胶方式做3度的出模角以便行位出模。 No draft in green area, suggest reducing plastic and draft angle 3degree to release the slider easily. 8 此处掏胶掏进去0.6MM. Here reduce 0.6mm plastic injection. 9 此处打1圆点或2圆点作为型腔号，请确认！ Make 1dot or 2s as the cavity number 10 产品此两处侧面绿色面为直身面，为防止产品此面脱花或拉伤，需增加出模角度0.5°（产品减胶） The green area have no draft angle, to a