2款韩式花苞头图解 3分钟学会.docVIP

2款韩式花苞头扎法图解 3分钟学会，爱美网美发分享丸子头的扎法图解步骤教程 爱美网 ? ? [2012-03-13 11:07] ?出处：爱美网 ?责任编辑：蓝蓝 相关专题： 花苞头 ??? 扎发 ??? DIY发型 ??? 导语： 温暖的春夏季快到了，又可以把头发扎起来，展现迷人的脖子与锁骨了，今天，爱美网美发小编教你两款超容易上手的甜美韩式花苞头，请你轻松搞掂甜美发型，无论是约会、见客还是见家长，都轻松应对，跟着小编一步一步，保证3分钟学会喔~ 　　 (点击图片进入下一页) 　　两款简单易学的花苞头扎发图解教程，保证让你3分钟上手。 　　 (点击图片进入下一页) 　　第一种：中心发散花苞头发型扎法(适用于中长发长度) 　　Step 1 　　扎一条高位马尾，抓取取一把头发(大概是马尾的1/4的发量)。 (点击图片进入下一页) 　　Step2 　　从发尾开始，将发束在手指上缠绕，直到发根部位。　 (点击图片进入下一页) 　　Step3 　　卷到发根之后，用发卡固定住。　 (点击图片进入下一页) 　　Step4 　　按照Step3的方法，取另一发束继续做　 (点击图片进入下一页) 　　Step5 　　继续取另一束发束，同样的动作，大概分四次卷发。? (点击图片进入下一页) 　　Step6 　　美丽的蓬松花苞头显型了。　 (点击图片进入下一页) 　　第2种：左右分离花苞头盘发教程(适用于长发) 　　Step1 　　扎一条中高位的马尾，把梳好的马尾折一下。? (点击图片进入下一页) 　　Step2 　　发尾处用发夹夹一下。　 (点击图片进入下一页) 　　步骤二 　　将盘好的花苞上下拉松。　 (点击图片进入下一页) 　　步骤三 　　再将盘好的花苞左右拉松。　 appearance of the weld appearance quality technical requirements of the project must not have a molten metal stream does not melt the base metal to weld, weld seam and heat-affected zone surface must not have cracks, pores, defects such as crater and ash, surface smoothing, weld and base metal should be evenly smooth transition. Width 2-3 mm from the edge of weld Groove. Surface reinforcement should be less than or equal to 1 + 0.2 times the slope edge width, and should not be greater than 4 mm. Depth of undercut should be less than or equal to 0.5 mm, total length of the welds on both sides undercut not exceed 10% of the weld length, and long continuous should not be greater than 100 mm. Wrong side should be less than or at 0.2T, and should not be greater than 2 mm (wall thickness mm t) incomplete or not allow 7.5 7.5.1 installation quality process standards of the electrical enclosure Cabinet surface is clean, neat, no significant phenomenon of convex, close to nature, close the door. 7.5.2 Cabinet Cabinet face paints no paint, returned to rusted, consistent color. 7.5.3 uniform indirect gap from top to bottom, slot width 1.5mm 7.5.4 adjacent Cabinet surface roughness is 0. 7.5.5 the cabinets firmly fixed, cr