11月26日油漆涂装专项方案.docVIP

目 录Contents 一、 编制说明 Reference 2 1．1编制依据Reference 2 1．2编制说明Description 2 1．3适用范围Applicable Scope 2 二、 油漆工艺Paint Repair Work Technique 2 2．1工艺流程图Process Flow Diagram (PFD) 2 2．2涂装工艺Repair Work Technique 3 2．3构件表面处理Member Surface Treatment 5 2．4油漆修补涂装Repairing Paint 6 油漆修补需在白天或有充分照明的环境下进行。 6 被修补涂层及基层的表面应干燥，无任何污染物（用干净的抹布充分擦净）。 6 三、 质量控制和质量保证措施 8 四、 安保措施 Safety Measures 10 编制说明 Reference 1．1编制依据Reference 施工图纸； Drawings for Construction 道康宁、东洋管理公司相关程序文件； Relevant Documents of Dow Corning and TOYO； 张家港油漆涂装标准 09.061.000； Zhangjiagang standard for painting and protective coatings,09.061.000； 《钢结构工程施工质量验收规范》GB50205-2001； Code for Construction Quality Acceptance of Steel Structure Engineering GB50205-2001； 《涂装前钢材表面锈蚀等级和除锈等级》GB8923。 Rust grades and preparation grades of steel surfaces before application of paints and related products, GB8923 1．2编制说明Description 本防腐油漆涂装施工方案是针对道康宁（张家港）有限公司19万吨/年有机硅聚硅氧烷项目（二期）工程钢结构工程而编制的。 This Anticorrosion Painting Construction Plan is compiled for Dow Corning 190kt/a Siloxane Project in Zhangjiagang (Phase 2) 1．3适用范围Applicable Scope 本方案仅适用于（二期）工程Team A区PartA＆C区钢结构工程的现场油漆修补及镀锌栏杆的涂装工作。 This Anticorrosion Painting Construction Plan is applicable only for site paint repair work in steel structure installation and zincing guardrail painting work in Team A of Phase 2 油漆工艺Paint Repair Work Technique 2．1工艺流程图Process Flow Diagram (PFD) 2．2涂装工艺Painting Technique 2．2．1确定修补范围Confirm the Regions that Needs Repair 检查构件外观，对所有在运输、倒运、现场焊接接等过程中破坏的涂层用记号笔作好标记，并标记出打磨处理的范围；对于栏杆，除了对现损伤涂层的修补外，还需要全面涂装面漆。 Check the appearance of members. Mark all the damaged coats caused during transportation and welding by marking pen. Highlight the area that needs grinding. For guardrail, besides the repairing of existing damage, overall painting should be carried out. 2．2．2油漆、工具进场验收 Inspection and Acceptance of Paint and Tools 2．2．2．1钢结构防腐油漆、稀释剂和固化剂的品种、规格、性能应与要求相符，检查油漆产品的质量合格证明文件、中文标志及检验报告；本工程钢结构油漆采用如下的油漆系统。 The type, specification, performance of anticorrosion paints, diluents and