- 1、本文档共73页,可阅读全部内容。
- 2、有哪些信誉好的足球投注网站(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
- 5、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
- 6、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们。
- 7、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 8、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
Classified Index: TH113.2 U.D.C: 621
Dissertation for the Master Degree of Engineering
REDUCING VIBRATION OF A FLEXIBLE ARM IN DIE BONDER BASED ON INPUT SHAPING
Candidate:Hua Huang
Candidate:
Hua Huang
Supervisor: Prof. Yu Wa
Academic Degree Applied for: Master of En
Specialty: Control Scie
Affiliation: Shenzhen Gr
Date of Defence: December, 2
Degree-Conferring-Institution: Harbin Instit
nce and Engineering aduate School
009
ute of Technology
I
I
摘 要
输入整形技术能有效抑制低阻尼柔性系统的残余振荡。因其应用简便,对建立 模型不确定性的鲁棒性好,从而在高速高精度的运动控制定位系统中得到了广泛的 应用。
论文首先介绍了输入整形的基本概念,并阐述了其设计的方法和步骤,进一步 说明了其能够抑制系统残余振荡的原因。然后通过仿真对比和实验验证的方法,对 输入整形器的鲁棒性进行分析,并得到了对实际工程应用具有一定参考价值的仿真 结果。由于固晶机柔性拾取臂在高速运动时的残余振荡会影响产品工艺质量,本文 针对这一问题,采用输入整形技术对其进行控制。
在实际应用中,由于固晶机对控制周期时间和定位精度的要求,考虑到输入整 形器的时滞性,首先利用 PID 控制来提高系统的定位精度,并提出基于输入整形 器的离线微分规划的方法来补偿该算法的时滞,同时抑制系统的残余振荡,从而达 到了高速高精度的控制要求。
关键词:输入整形;残余振荡;固晶机;高速高精度;
II
II
ABSTRACT
Input shaping is a method of reducing residual vibrations of low damped flexible system. Due to its simplicity, effectiveness, and robust to modeling uncertain, this technique has been widely used in high-speed and high-precision motion controlled positioning machines.
This dissertation firstly introduces the basic theory of input shaping, and explains the methods and steps to design input shaper particularly, from which gives the inherent essence to suppress the residual vibration of flexible system. By simulation and comparison, the research of the robustness of the input shaper is given then. How the error of the natural frequency and damping will perform the response of the system will be discussed herein. The results supply greatly references for the application lately. Finally, input shaping was used in the control of the flexible operation-arm, which has the residual vibration problem when moving in high speed in die bonder system.
Considering the time delay property of input shaper, and the shorter control time circle and accuracy in die bonder, a new method based on offline derivative profile was used here.
您可能关注的文档
- 基于树形奇偶机的神经网络同步方案-计算机系统结构专业论文.docx
- 基于微控制器的自动扶梯电控系统-计算机技术专业论文.docx
- 基于可重构柔性试验床的管控平台研究-计算机应用专业论文.docx
- 基于前端处理噪声环境下稳健的说话人识别研究-信号与信息处理专业论文.docx
- 基于特征提取的篡改图像取证研究-计算机应用技术专业论文.docx
- 基于容性设备泄漏电流的嵌入式电网过电压在线监测系统研究-电气工程专业论文.docx
- 基于手指的人机交互系统研究与实现-电路与系统专业论文.docx
- 基于网格的任务调度算法研究-计算机应用技术专业论文.docx
- 基于随机影响的多智能体系统的一致性与同步-运筹学与控制论专业论文.docx
- 基于决策树分类算法的Web文本分类分析-计算机应用技术专业论文.docx
文档评论(0)